Revision as of 17:02, 19 July 2018
Information about message (contribute ) This message has no documentation.
If you know where or how this message is used, you can help other translators by adding documentation to this message.
Message definition (FAQ )
If you have no output, this mean the GhostBSD network configuration system have not detected your WiFi card. The next step for you will be to look if GhostBSD have your WiFi drivers install. : <code>sudo ifconfig | grep -B 3 802.11</code> In this case run0 is the WiFi drivers. <pre> run0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:1e:e5:e6:5d:1 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: IEEE 802.11 Wireless Ethernet autoselect mode 11a </pre> If you have an output similar from the example above, you need to configure the file ''/etc/rc.conf''. : <code>sudo ee /etc/rc.conf</code> Add those line in the file ''/etc/rc.conf'' (Replace run0 by your drivers). <pre> wlans_run0="wlan0" ifconfig_wlan0="WPA DHCP" </pre> [[wikipedia:en:Esc key|Esc]] and save the file. Now you need to restart <code>netif</code>. : <code>sudo /etc/rc.d/netif restart</code> Your wifi is now configured, you might have to turn wlan0 up. : <code>sudo ifconfig wlan0 up</code>
If you have no output, this mean the GhostBSD network configuration system have not detected your WiFi card. The next step for you will be to look if GhostBSD have your WiFi drivers install.
: <code>sudo ifconfig | grep -B 3 802.11</code>
In this case run0 is the WiFi drivers.
<pre>
run0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 00:1e:e5:e6:5d:1
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect mode 11a
</pre>
If you have an output similar from the example above, you need to configure the file ''/etc/rc.conf''.
: <code>sudo ee /etc/rc.conf</code>
Add those line in the file ''/etc/rc.conf'' (Replace run0 by your drivers).
<pre>
wlans_run0="wlan0"
ifconfig_wlan0="WPA DHCP"
</pre>
[[wikipedia:en:Esc key|Esc]] and save the file. Now you need to restart <code>netif</code>.
: <code>sudo /etc/rc.d/netif restart</code>
Your wifi is now configured, you might have to turn wlan0 up.
: <code>sudo ifconfig wlan0 up</code>
Translation Si no genera ninguna salida, significa que la configuracion de red de GhostBSD no detecto su tarjeta inalambrica. Lo proximo que debería hacer es revisar si GhostBSD tiene el driver de su tarjeta inalambrica instalada : <code>sudo ifconfig | grep -B 3 802.11</code> En este caso run0 es el driver de la tarjeta inalambrica. <pre> run0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:1e:e5:e6:5d:1 nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> media: IEEE 802.11 Wireless Ethernet autoselect mode 11a </pre> Si tienes una salida similar al ejemplo anterior, necesita configurar el archivo ''/etc/rc.conf''. : <code>sudo ee /etc/rc.conf</code> Agregue estas lineas al archivo ''/etc/rc.conf'' (Reemplaze run0 con su driver). <pre> wlans_run0="wlan0" ifconfig_wlan0="WPA DHCP" </pre> [[wikipedia:en:Esc key|Esc]] y guarde el archivo. Ahora necesita reiniciar el paquete <code>netif</code>. : <code>sudo /etc/rc.d/netif restart</code> Su tarjeta inalambrica esta configurada, deberia encender su red wlan0 up. : <code>sudo ifconfig wlan0 up</code> Si no genera ninguna salida, significa que la configuracion de red de GhostBSD no detecto su tarjeta inalambrica. Lo proximo que debería hacer es revisar si GhostBSD tiene el driver de su tarjeta inalambrica instalada
sudo ifconfig | grep -B 3 802.11
En este caso run0 es el driver de la tarjeta inalambrica.
run0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 2290
ether 00:1e:e5:e6:5d:1
nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
media: IEEE 802.11 Wireless Ethernet autoselect mode 11a
Si tienes una salida similar al ejemplo anterior, necesita configurar el archivo /etc/rc.conf .
sudo ee /etc/rc.conf
Agregue estas lineas al archivo /etc/rc.conf (Reemplaze run0 con su driver).
wlans_run0="wlan0"
ifconfig_wlan0="WPA DHCP"
Esc y guarde el archivo. Ahora necesita reiniciar el paquete netif
.
sudo /etc/rc.d/netif restart
Su tarjeta inalambrica esta configurada, deberia encender su red wlan0 up.
sudo ifconfig wlan0 up